Загрузки для TL-SG2210P
- Product Overview
- Manual
Setup Video
-
How to Set Up the Whole Network of Gateway, Switches, and EAPs Using Omada SDN Controller
This video will demonstration how to do a full configuration with TP-Link Omada products including gateway, switches and EAPs. As an example, we are going to build the wired and wireless networks from scratch at our TP-Link Office. The setup consists of 7 steps: Step 1. Log in to the Controller Step 2. Adopt Devices Step 3. View Dashboard and Menus Step 4. Set up WAN Step 5. Set up LAN and VLANs Step 6. Set up Wi-Fi Step 7. Set up ACL
Больше Меньше
FAQ
- How to Configure Management VLAN on TP-Link Smart and Managed Switches Using the New GUI
- Troubleshooting multicast video issues on Omada switches
- How to configure Switch Port Mirroring on Omada Controller
- Как настроить 802.1Q VLAN на Smart и управляемых коммутаторах с новым интерфейсом?
- How to configure LACP on our Smart/ Managed Switch
- Как настроить IGMP Snooping для работы IPTV на управляемых коммутаторах 2‑го уровня с новым интерфейсом?
- Troubleshooting guide for ARP Learning Failure
- How to configure Storm Control on Omada Switch via Omada Controller
- How to configure Class of Service (CoS) through Omada Controller
- How to configure Jumbo Frame on Omada Controller
- Suggested configurations for AVoIP protocols on Omada Switches
- How to configure Auto-VoIP on Omada Switches via Omada Controller
- Configuration guide of DHCP Options on Omada Switch
- Troubleshooting of Layer 2 Multicast Failure
- How to configure IGMP Snooping on Omada switches for hotel IPTV scenario
- How to configure 802.1X VLAN Assignment on Omada Controller
- Recommended ACL configuration on Omada Switch for common scenarios
- В чём разница между главным администратором, администратором и посетителем в системе Omada?
- Как использовать команду Ping в приложении Omada
- Что делать, если не удаётся получить доступ к веб‑интерфейсу коммутатора TP‑Link?
- Do you still have any doubt about the effect of QoS on the Switch of TP-Link?
- Getting started without an Omada Controller
- How to configure Management VLANs for Omada Switches and APs (for SOHO scenario)
- How to configure Management VLANs for Omada Switches and APs (for Business scenario)
- What should I do if my switch has no Internet access?
- What should I do if my Internet from switch is unstable?
- How to configure DHCP Auto Install to let switch get configuration file and image from TFTP server
- How to build an 802.1X access authentication system using Switches on Omada Controller
- Why my PoE powered device cannot work properly when connected to the PoE Switch？
- How to block an illegal client with Certain IP address from getting access to the network using TP-Link Managed Switches
- В чём заключаются различия в функциях и способах применения различных серий коммутаторов?
- How to configure Optical Line Terminal (OLT) and Omada Switch with XM60A
- How to configure LAG (LACP) on Omada Switches via Omada Controller
- How to configure VLAN Interfaces and Static Routes on Omada Switches
- Troubleshooting for Voice VLAN and Auto VoIP
- What to do if devices in the same VLAN fail to communicate with each other when connected to TP-Link switch
- Best practice to prevent network loops with Omada SDN solution
- How to configure switch as DHCP server on Standalone mode
- Using Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported)
- How to Manage Omada Devices at Different Sites Using Omada SDN Controller via Port Forwarding (Controller 5.0 or Above)
- How to Manage Omada Devices at Different Sites Using Omada SDN Controller via VPN (Controller 5.0 or Above)
- Что такое двухэтапная аутентификация и как её включить в системе Omada
- Typical CLI Configuration Examples for TP-Link JetStream Switch
- How to test the Jumbo Frame pass-through feature on TP-Link switches
- How to configure RSTP on TP-Link switches using the old GUI
- How to change the IP address of the smart and managed switches using the old GUI and CLI
- How to configure MAC ACL on Smart/Managed switch
- How to choose PoE switch
- How to check and modify VLANs on a TP-Link JetStream switch via SNMP
- How to achieve AAA Authentication through TACACS + server on the switch
- How to configure OpenSSH 7.0(and above) to login smart and managed switches?
|
TL-SG2210P(UN)_V3_20200730 |
Загрузить | |
|---|---|---|
| Дата публикации: 2022-01-20 | Язык: Английский | Размер файла: 8.46 MB |
|
Notes: |
||
|
TL-SG2210P(UN)_V3.2_3.20.2_20210806 |
Загрузить | |
|---|---|---|
| Дата публикации: 2021-08-26 | Язык: Английский | Размер файла: 8.81 MB |
|
This firmware is fully adapted to the Omada SDN platform but only compatible with Omada controller v4.3.5 or above. If you are using an old Omada controller and plan to upgrade firmware for EAP, then you must upgrade the Omada controller as well. Please follow the Upgrade Guide to upgrade the Omada Controller.
Enhancement/Bug Fixed: 1. Fully adapt to Omada SDN Controller 4.3.5. 2. Improved the stability of the Layer-3 interface. 3. Fixed the bug of invalid traffic statistics. 4. Fixed the bug when forwarding bi-directional traffic with specific applications.
Notes: 1. For TL-SG2210P(UN) 3.0,3.20 and 3.26. 2. This firmware is applied to Omada APP of version 3.0.x or above. 3. Please upgrade the switch to the middle firmware Build 20210407 first before upgrading to this firmware or later one. |
||
|
TL-SG2210P(UN)_V3_20210407 |
Загрузить | |
|---|---|---|
| Дата публикации: 2021-05-26 | Язык: Английский | Размер файла: 8.61 MB |
|
New Feature/Enhancement: |
||
Приложение
- Omada APP
-
Приложение Omada компании TP‑Link позволяет выполнять настройку параметров, мониторинг сети и управление клиентскими устройствами прямо с телефона или планшета (список совместимых устройств).
Примечание: коммутаторы и маршрутизаторы SDN могут работать с приложением Omada только в режиме контроллера. Для работы приложения Omada необходимо обновить прошивку устройства до последней версии.